Bright Melbourne bedroom with a built-in wardrobe fitted with new frameless sliding doors in silver mirror and bronze tinted glass

Replacing Old Mirrored Wardrobe Doors: Updating Without Rebuilding Your Robe

Yes, you can usually replace old mirrored wardrobe doors without rebuilding the robe. Replacement wardrobe doors are made to measure for the existing opening, so the shelving, hanging rails and drawers inside stay as they are. The existing tracks can sometimes be reused, but only if they are in good condition and suit the new doors, which is checked when the opening is measured. Replacing the doors is also the time to move to a Grade A safety mirror or to a tinted or coloured glass finish.

Key takeaways

  • Replacing the doors changes the front of the robe. The inside fit-out and the wall opening stay.
  • Old tracks are reused only if they are in good condition and compatible with the new doors. Worn or mismatched tracks are replaced.
  • A mirror on a wardrobe door is generally expected to be a Grade A safety mirror. Older doors may not be, so check for a safety mark.
  • A single damaged panel can often be replaced on its own. A dated or worn set is usually better replaced as a whole.
  • Design Inferno’s glass and mirror wardrobe doors start from $450, quoted on your opening’s width and height.

What stays and what changes when you replace wardrobe doors?

Wardrobe door replacement changes the front of the wardrobe and leaves the structure behind it. The table shows what usually happens to each part.

Part of the robeWhat usually happens
Shelving, hanging rails and drawersStay as they are
Wall opening, bulkhead and wallsStay. The new doors are made to fit the opening
Top and bottom tracksReused if in good condition and compatible; otherwise replaced
Door panels and framesReplaced with new made-to-measure panels
Rollers and soft-closeNew rollers come with the new doors; soft-close can be added

PRACTICAL TIP

If you are also changing the flooring, do it before the doors are measured. New carpet or timber changes the height between the tracks, and the doors are made to that height.

Cutaway diagram of a built-in wardrobe showing the shelving, rails and opening that stay, and the sliding door panels and tracks that are replaced

Should you repair or replace mirrored wardrobe doors?

Repair the hardware or replace a single panel when one part is the problem, and replace the whole set when every door is affected, such as missing safety marks or a dated style.

Explore Our Products

What you noticeLikely causeUsual fix
Door drags or jumps the trackWorn rollers, dirt in the bottom track or a bent trackCheck the rollers and track first
One cracked or chipped panelImpact damageReplace that panel
Black spots or edges on the mirrorDesilvering, where moisture or harsh cleaners attack the silver layer, usually starting at the edgesReplace the affected panels or the set
No safety mark on the mirrorMirror may not be a Grade A safety mirrorReplace with safety-backed mirror
Dated frames or finishStyle, not damageReplace the set with a new finish and frame style
Bent frames or panels that no longer close squareWear over many yearsReplace the set, and check the tracks

For a damaged panel, Design Inferno asks you to contact it to arrange a replacement. On a framed system, a single panel can usually be removed and replaced on its own.

Can you keep your existing wardrobe tracks?

Existing wardrobe door tracks can be reused only if they are in good condition and compatible with the new door system. Design Inferno checks the tracks when it measures the opening and tells you before you order whether they can stay. Worn or incompatible tracks are replaced as part of the job.

What usually decides it:

  • Condition: dents, bends, worn running surfaces or loose fixings.
  • Compatibility: whether the new panels and rollers suit the track profile.
  • Fit: whether the track still sits square and level across the opening.

COMMON MISTAKE

Ordering new panels to suit old tracks without having the tracks checked. A worn track makes new doors drag, so the cost of new tracks is usually lower than the cost of doors that never run smoothly.

Is your old mirror safety glass?

A mirror on a wardrobe door is generally expected to be Grade A safety glazing, and older doors may not use it. AS 1288, the Australian Standard for glass in buildings, sets where safety glass is needed, and AS/NZS 2208:2023 sets how safety glazing is tested and graded. For a sliding mirror door, that usually means a safety-backed mirror, which has a vinyl film bonded to the back. Ask your glazier to confirm the right product for your doors.

To check your doors, look in a corner of each panel for a permanent mark. Under the NCC glazing provisions, safety glass used in a building must be marked with permanent etching or a label that cannot be reused, showing the standard, the grade, the thickness, the glass type and the maker or supplier. No mark means you cannot confirm the mirror is safety glass.

IMPORTANT TO KNOW

Don’t glue a new mirror or panel over an old door to update it. It adds weight the rollers and track were not designed to carry, and the doors can start to drag or jump the track.

For a full guide to wardrobe door glass, read what glass is used for wardrobe doors.

Diagram comparing a broken plain mirror with a broken safety-backed mirror held together by its vinyl film, with a close-up of a safety glass mark in a panel corner

What can replace old mirrored wardrobe doors?

Old mirrored wardrobe doors can be replaced with new mirror, tinted glass, coloured glass or solid panels. Design Inferno makes sliding wardrobe doors in mirror, tinted glass and coloured glass, with MDF and vinyl for solid panels. Mirrored sliding wardrobe doors are still a practical choice for small bedrooms because they reflect light and double as a full-length mirror.

FinishSuitsTrade-off
MirrorSmall rooms that need light and a full-length mirrorShows fingerprints
Tinted mirror or glassA softer reflectionLess light bounced around the room
Colour glassA feature wall in a chosen colourNo mirror
MDF or vinylA solid, non-reflective panelNo glass finish

Frame styles are traditional framed, semi-frameless, frameless and shoji, in 2, 3 or 4 panel layouts. Soft-close is available. You can see finishes at the Keilor Park showroom or preview colours online with the colour simulator. For a side-by-side comparison of finishes, read mirror vs tinted vs colour glass wardrobe doors.

How does wardrobe door replacement work?

Wardrobe door replacement has three steps: the opening and tracks are measured and checked, the doors are made to size, and the new doors are installed. Design Inferno measures, manufactures and installs custom wardrobe doors across Melbourne. Replacement sliding wardrobe doors go through these steps:

  1. Measure: the wardrobe opening is measured, and the existing tracks are checked.
  2. Manufacture: the doors are made to size in the Keilor Park factory.
  3. Install: the tracks and doors are fitted and checked to slide smoothly.

PRACTICAL TIP

Ask at the quote stage what happens to the old doors. Large mirror panels are heavy and awkward to move, so plan for them before installation day.

What does it cost to replace mirrored wardrobe doors?

Design Inferno’s glass and mirror wardrobe doors start from $450 at the time of writing (November 2026). The final price depends on:

  • the opening size
  • the number of panels
  • the finish
  • the frame style
  • soft-close
  • installation requirements

Send the opening’s width and height for a quote. Replacing the doors only is generally a smaller job than rebuilding the robe, because the joinery behind the doors stays.

What should you check before getting a quote?

Measure the opening, count the panels, and check the tracks and each mirror panel for a safety mark before you ask for a quote.

QUICK CHECKLIST

  • Measure the opening width and height at the top, middle and bottom, and note the smallest figure.
  • Count the current panels and note whether you want the same number.
  • Take photos of the top and bottom tracks, close-up and in full.
  • Check each mirror panel for a safety mark.
  • Note skirting, cornice and flooring near the opening, and any flooring changes planned.
  • Shortlist two or three finishes and a frame style.

Conclusion

Old mirrored wardrobe doors can usually be replaced without touching the robe behind them. New panels are made to the existing opening, the tracks are reused when they are in good condition and compatible, and the replacement is the right time to move to Grade A safety mirror or a new finish.

Design Inferno measures, manufactures and installs custom sliding wardrobe doors across Melbourne, made to measure in its Keilor Park factory. Send your opening’s width and height to get a quote for glass wardrobe doors, or contact the team.

Frequently asked questions

Sliding wardrobe doors can be replaced without new tracks if the existing tracks are in good condition and compatible with the new doors. They are checked when the opening is measured, and worn or incompatible tracks are replaced.

You can often replace just one panel. On a framed system, a single damaged panel can usually be removed and replaced. A new panel may not match the others if the set is old, so a full replacement can look better.

Old mirrored wardrobe doors are safe only if the mirror is a Grade A safety mirror. Check each panel for a permanent safety mark. Without one, you cannot confirm the mirror is safety glass, and replacing it with safety-backed mirror is the safer option.

Design Inferno’s glass and mirror wardrobe doors start from $450. The price depends on the opening size, number of panels, finish, frame style, soft-close and installation requirements.

Mirrored wardrobe doors are still practical in small bedrooms because they reflect light and work as a full-length mirror. Heavy frames and plain silver mirror can look dated, so frameless panels or tinted and coloured glass are common updates.

Yes, you can change from mirror to glass. Replacement sliding doors can be mirror, tinted mirror, glass, coloured glass, MDF or vinyl, so the new set does not have to match the old one.